High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
fbcon: fix integer overflow in fbcon_do_set_font
Fix integer overflow vulnerabilities in fbcon_do_set_font() where font
size calculations could overflow when handling user-controlled font
parameters.
The vulnerabilities occur when:
1. CALC_FONTSZ(h, pitch, charcount) performs h * pith * charcount
multiplication with user-controlled values that can overflow.
2. FONT_EXTRA_WORDS * sizeof(int) + size addition can also overflow
3. This results in smaller allocations than expected, leading to buffer
overflows during font data copying.
Add explicit overflow checking using check_mul_overflow() and
check_add_overflow() kernel helpers to safety validate all size
calculations before allocation.
Published Oct 15, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
iommufd: Fix race during abort for file descriptors
fput() doesn't actually call file_operations release() synchronously, it
puts the file on a work queue and it will be released eventually.
This is normally fine, except for iommufd the file and the iommufd_object
are tied to gether. The file has the object as it's private_data and holds
a users refcount, while the object is expected to remain alive as long as
the file is.
When the allocation of a new object aborts before installing the file it
will fput() the file and then go on to immediately kfree() the obj. This
causes a UAF once the workqueue completes the fput() and tries to
decrement the users refcount.
Fix this by putting the core code in charge of the file lifetime, and call
__fput_sync() during abort to ensure that release() is called before
kfree. __fput_sync() is a bit too tricky to open code in all the object
implementations. Instead the objects tell the core code where the file
pointer is and the core will take care of the life cycle.
If the object is successfully allocated then the file will hold a users
refcount and the iommufd_object cannot be destroyed.
It is worth noting that close(); ioctl(IOMMU_DESTROY); doesn't have an
issue because close() is already using a synchronous version of fput().
The UAF looks like this:
BUG: KASAN: slab-use-after-free in iommufd_eventq_fops_release+0x45/0xc0 drivers/iommu/iommufd/eventq.c:376
Write of size 4 at addr ffff888059c97804 by task syz.0.46/6164
CPU: 0 UID: 0 PID: 6164 Comm: syz.0.46 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/18/2025
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xcd/0x630 mm/kasan/report.c:482
kasan_report+0xe0/0x110 mm/kasan/report.c:595
check_region_inline mm/kasan/generic.c:183 [inline]
kasan_check_range+0x100/0x1b0 mm/kasan/generic.c:189
instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:400 [inline]
__refcount_dec include/linux/refcount.h:455 [inline]
refcount_dec include/linux/refcount.h:476 [inline]
iommufd_eventq_fops_release+0x45/0xc0 drivers/iommu/iommufd/eventq.c:376
__fput+0x402/0xb70 fs/file_table.c:468
task_work_run+0x14d/0x240 kernel/task_work.c:227
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
exit_to_user_mode_loop+0xeb/0x110 kernel/entry/common.c:43
exit_to_user_mode_prepare include/linux/irq-entry-common.h:225 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:175 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:210 [inline]
do_syscall_64+0x41c/0x4c0 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Published Oct 15, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
xfrm: xfrm_alloc_spi shouldn't use 0 as SPI
x->id.spi == 0 means "no SPI assigned", but since commit
94f39804d891 ("xfrm: Duplicate SPI Handling"), we now create states
and add them to the byspi list with this value.
__xfrm_state_delete doesn't remove those states from the byspi list,
since they shouldn't be there, and this shows up as a UAF the next
time we go through the byspi list.
Published Oct 13, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
crypto: af_alg - Disallow concurrent writes in af_alg_sendmsg
Issuing two writes to the same af_alg socket is bogus as the
data will be interleaved in an unpredictable fashion. Furthermore,
concurrent writes may create inconsistencies in the internal
socket state.
Disallow this by adding a new ctx->write field that indiciates
exclusive ownership for writing.
Published Oct 13, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
io_uring: fix incorrect io_kiocb reference in io_link_skb
In io_link_skb function, there is a bug where prev_notif is incorrectly
assigned using 'nd' instead of 'prev_nd'. This causes the context
validation check to compare the current notification with itself instead
of comparing it with the previous notification.
Fix by using the correct prev_nd parameter when obtaining prev_notif.
Published Oct 9, 2025 · Updated Jul 30, 2026
High · CVSS 7.5
In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix untrusted unsigned subtract
Fix the following Smatch static checker warning:
net/rxrpc/rxgk_app.c:65 rxgk_yfs_decode_ticket()
warn: untrusted unsigned subtract. 'ticket_len - 10 * 4'
by prechecking the length of what we're trying to extract in two places in
the token and decoding for a response packet.
Also use sizeof() on the struct we're extracting rather specifying the size
numerically to be consistent with the other related statements.
Published Oct 9, 2025 · Updated Jul 30, 2026
High · CVSS 8.8
In the Linux kernel, the following vulnerability has been resolved:
iommu/amd/pgtbl: Fix possible race while increase page table level
The AMD IOMMU host page table implementation supports dynamic page table levels
(up to 6 levels), starting with a 3-level configuration that expands based on
IOVA address. The kernel maintains a root pointer and current page table level
to enable proper page table walks in alloc_pte()/fetch_pte() operations.
The IOMMU IOVA allocator initially starts with 32-bit address and onces its
exhuasted it switches to 64-bit address (max address is determined based
on IOMMU and device DMA capability). To support larger IOVA, AMD IOMMU
driver increases page table level.
But in unmap path (iommu_v1_unmap_pages()), fetch_pte() reads
pgtable->[root/mode] without lock. So its possible that in exteme corner case,
when increase_address_space() is updating pgtable->[root/mode], fetch_pte()
reads wrong page table level (pgtable->mode). It does compare the value with
level encoded in page table and returns NULL. This will result is
iommu_unmap ops to fail and upper layer may retry/log WARN_ON.
CPU 0 CPU 1
------ ------
map pages unmap pages
alloc_pte() -> increase_address_space() iommu_v1_unmap_pages() -> fetch_pte()
pgtable->root = pte (new root value)
READ pgtable->[mode/root]
Reads new root, old mode
Updates mode (pgtable->mode += 1)
Since Page table level updates are infrequent and already synchronized with a
spinlock, implement seqcount to enable lock-free read operations on the read path.
Published Oct 9, 2025 · Updated Jul 30, 2026
High · CVSS 7.3
In the Linux kernel, the following vulnerability has been resolved:
gpiolib: acpi: initialize acpi_gpio_info struct
Since commit 7c010d463372 ("gpiolib: acpi: Make sure we fill struct
acpi_gpio_info"), uninitialized acpi_gpio_info struct are passed to
__acpi_find_gpio() and later in the call stack info->quirks is used in
acpi_populate_gpio_lookup. This breaks the i2c_hid_cpi driver:
[ 58.122916] i2c_hid_acpi i2c-UNIW0001:00: HID over i2c has not been provided an Int IRQ
[ 58.123097] i2c_hid_acpi i2c-UNIW0001:00: probe with driver i2c_hid_acpi failed with error -22
Fix this by initializing the acpi_gpio_info pass to __acpi_find_gpio()
Published Oct 9, 2025 · Updated Jul 30, 2026
High · CVSS 7.1
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: increase scan_ies_len for S1G
Currently the S1G capability element is not taken into account
for the scan_ies_len, which leads to a buffer length validation
failure in ieee80211_prep_hw_scan() and subsequent WARN in
__ieee80211_start_scan(). This prevents hw scanning from functioning.
To fix ensure we accommodate for the S1G capability length.
Published Oct 9, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
igc: don't fail igc_probe() on LED setup error
When igc_led_setup() fails, igc_probe() fails and triggers kernel panic
in free_netdev() since unregister_netdev() is not called. [1]
This behavior can be tested using fault-injection framework, especially
the failslab feature. [2]
Since LED support is not mandatory, treat LED setup failures as
non-fatal and continue probe with a warning message, consequently
avoiding the kernel panic.
[1]
kernel BUG at net/core/dev.c:12047!
Oops: invalid opcode: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 937 Comm: repro-igc-led-e Not tainted 6.17.0-rc4-enjuk-tnguy-00865-gc4940196ab02 #64 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:free_netdev+0x278/0x2b0
[...]
Call Trace:
<TASK>
igc_probe+0x370/0x910
local_pci_probe+0x3a/0x80
pci_device_probe+0xd1/0x200
[...]
[2]
#!/bin/bash -ex
FAILSLAB_PATH=/sys/kernel/debug/failslab/
DEVICE=0000:00:05.0
START_ADDR=$(grep " igc_led_setup" /proc/kallsyms \
| awk '{printf("0x%s", $1)}')
END_ADDR=$(printf "0x%x" $((START_ADDR + 0x100)))
echo $START_ADDR > $FAILSLAB_PATH/require-start
echo $END_ADDR > $FAILSLAB_PATH/require-end
echo 1 > $FAILSLAB_PATH/times
echo 100 > $FAILSLAB_PATH/probability
echo N > $FAILSLAB_PATH/ignore-gfp-wait
echo $DEVICE > /sys/bus/pci/drivers/igc/bind
Published Oct 9, 2025 · Updated Jul 30, 2026
High · CVSS 8.8
In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: avoid buffer overflow in WID string configuration
Fix the following copy overflow warning identified by Smatch checker.
drivers/net/wireless/microchip/wilc1000/wlan_cfg.c:184 wilc_wlan_parse_response_frame()
error: '__memcpy()' 'cfg->s[i]->str' copy overflow (512 vs 65537)
This patch introduces size check before accessing the memory buffer.
The checks are base on the WID type of received data from the firmware.
For WID string configuration, the size limit is determined by individual
element size in 'struct wilc_cfg_str_vals' that is maintained in 'len' field
of 'struct wilc_cfg_str'.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
um: virtio_uml: Fix use-after-free after put_device in probe
When register_virtio_device() fails in virtio_uml_probe(),
the code sets vu_dev->registered = 1 even though
the device was not successfully registered.
This can lead to use-after-free or other issues.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
qed: Don't collect too many protection override GRC elements
In the protection override dump path, the firmware can return far too
many GRC elements, resulting in attempting to write past the end of the
previously-kmalloc'ed dump buffer.
This will result in a kernel panic with reason:
BUG: unable to handle kernel paging request at ADDRESS
where "ADDRESS" is just past the end of the protection override dump
buffer. The start address of the buffer is:
p_hwfn->cdev->dbg_features[DBG_FEATURE_PROTECTION_OVERRIDE].dump_buf
and the size of the buffer is buf_size in the same data structure.
The panic can be arrived at from either the qede Ethernet driver path:
[exception RIP: qed_grc_dump_addr_range+0x108]
qed_protection_override_dump at ffffffffc02662ed [qed]
qed_dbg_protection_override_dump at ffffffffc0267792 [qed]
qed_dbg_feature at ffffffffc026aa8f [qed]
qed_dbg_all_data at ffffffffc026b211 [qed]
qed_fw_fatal_reporter_dump at ffffffffc027298a [qed]
devlink_health_do_dump at ffffffff82497f61
devlink_health_report at ffffffff8249cf29
qed_report_fatal_error at ffffffffc0272baf [qed]
qede_sp_task at ffffffffc045ed32 [qede]
process_one_work at ffffffff81d19783
or the qedf storage driver path:
[exception RIP: qed_grc_dump_addr_range+0x108]
qed_protection_override_dump at ffffffffc068b2ed [qed]
qed_dbg_protection_override_dump at ffffffffc068c792 [qed]
qed_dbg_feature at ffffffffc068fa8f [qed]
qed_dbg_all_data at ffffffffc0690211 [qed]
qed_fw_fatal_reporter_dump at ffffffffc069798a [qed]
devlink_health_do_dump at ffffffff8aa95e51
devlink_health_report at ffffffff8aa9ae19
qed_report_fatal_error at ffffffffc0697baf [qed]
qed_hw_err_notify at ffffffffc06d32d7 [qed]
qed_spq_post at ffffffffc06b1011 [qed]
qed_fcoe_destroy_conn at ffffffffc06b2e91 [qed]
qedf_cleanup_fcport at ffffffffc05e7597 [qedf]
qedf_rport_event_handler at ffffffffc05e7bf7 [qedf]
fc_rport_work at ffffffffc02da715 [libfc]
process_one_work at ffffffff8a319663
Resolve this by clamping the firmware's return value to the maximum
number of legal elements the firmware should return.
Published Oct 4, 2025 · Updated Jul 30, 2026
Critical · CVSS 9.8
In the Linux kernel, the following vulnerability has been resolved:
ice: fix Rx page leak on multi-buffer frames
The ice_put_rx_mbuf() function handles calling ice_put_rx_buf() for each
buffer in the current frame. This function was introduced as part of
handling multi-buffer XDP support in the ice driver.
It works by iterating over the buffers from first_desc up to 1 plus the
total number of fragments in the frame, cached from before the XDP program
was executed.
If the hardware posts a descriptor with a size of 0, the logic used in
ice_put_rx_mbuf() breaks. Such descriptors get skipped and don't get added
as fragments in ice_add_xdp_frag. Since the buffer isn't counted as a
fragment, we do not iterate over it in ice_put_rx_mbuf(), and thus we don't
call ice_put_rx_buf().
Because we don't call ice_put_rx_buf(), we don't attempt to re-use the
page or free it. This leaves a stale page in the ring, as we don't
increment next_to_alloc.
The ice_reuse_rx_page() assumes that the next_to_alloc has been incremented
properly, and that it always points to a buffer with a NULL page. Since
this function doesn't check, it will happily recycle a page over the top
of the next_to_alloc buffer, losing track of the old page.
Note that this leak only occurs for multi-buffer frames. The
ice_put_rx_mbuf() function always handles at least one buffer, so a
single-buffer frame will always get handled correctly. It is not clear
precisely why the hardware hands us descriptors with a size of 0 sometimes,
but it happens somewhat regularly with "jumbo frames" used by 9K MTU.
To fix ice_put_rx_mbuf(), we need to make sure to call ice_put_rx_buf() on
all buffers between first_desc and next_to_clean. Borrow the logic of a
similar function in i40e used for this same purpose. Use the same logic
also in ice_get_pgcnts().
Instead of iterating over just the number of fragments, use a loop which
iterates until the current index reaches to the next_to_clean element just
past the current frame. Unlike i40e, the ice_put_rx_mbuf() function does
call ice_put_rx_buf() on the last buffer of the frame indicating the end of
packet.
For non-linear (multi-buffer) frames, we need to take care when adjusting
the pagecnt_bias. An XDP program might release fragments from the tail of
the frame, in which case that fragment page is already released. Only
update the pagecnt_bias for the first descriptor and fragments still
remaining post-XDP program. Take care to only access the shared info for
fragmented buffers, as this avoids a significant cache miss.
The xdp_xmit value only needs to be updated if an XDP program is run, and
only once per packet. Drop the xdp_xmit pointer argument from
ice_put_rx_mbuf(). Instead, set xdp_xmit in the ice_clean_rx_irq() function
directly. This avoids needing to pass the argument and avoids an extra
bit-wise OR for each buffer in the frame.
Move the increment of the ntc local variable to ensure its updated *before*
all calls to ice_get_pgcnts() or ice_put_rx_mbuf(), as the loop logic
requires the index of the element just after the current frame.
Now that we use an index pointer in the ring to identify the packet, we no
longer need to track or cache the number of fragments in the rx_ring.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
cnic: Fix use-after-free bugs in cnic_delete_task
The original code uses cancel_delayed_work() in cnic_cm_stop_bnx2x_hw(),
which does not guarantee that the delayed work item 'delete_task' has
fully completed if it was already running. Additionally, the delayed work
item is cyclic, the flush_workqueue() in cnic_cm_stop_bnx2x_hw() only
blocks and waits for work items that were already queued to the
workqueue prior to its invocation. Any work items submitted after
flush_workqueue() is called are not included in the set of tasks that the
flush operation awaits. This means that after the cyclic work items have
finished executing, a delayed work item may still exist in the workqueue.
This leads to use-after-free scenarios where the cnic_dev is deallocated
by cnic_free_dev(), while delete_task remains active and attempt to
dereference cnic_dev in cnic_delete_task().
A typical race condition is illustrated below:
CPU 0 (cleanup) | CPU 1 (delayed work callback)
cnic_netdev_event() |
cnic_stop_hw() | cnic_delete_task()
cnic_cm_stop_bnx2x_hw() | ...
cancel_delayed_work() | /* the queue_delayed_work()
flush_workqueue() | executes after flush_workqueue()*/
| queue_delayed_work()
cnic_free_dev(dev)//free | cnic_delete_task() //new instance
| dev = cp->dev; //use
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the cyclic delayed work item is properly canceled and that any
ongoing execution of the work item completes before the cnic_dev is
deallocated. Furthermore, since cancel_delayed_work_sync() uses
__flush_work(work, true) to synchronously wait for any currently
executing instance of the work item to finish, the flush_workqueue()
becomes redundant and should be removed.
This bug was identified through static analysis. To reproduce the issue
and validate the fix, I simulated the cnic PCI device in QEMU and
introduced intentional delays — such as inserting calls to ssleep()
within the cnic_delete_task() function — to increase the likelihood
of triggering the bug.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
octeontx2-pf: Fix use-after-free bugs in otx2_sync_tstamp()
The original code relies on cancel_delayed_work() in otx2_ptp_destroy(),
which does not ensure that the delayed work item synctstamp_work has fully
completed if it was already running. This leads to use-after-free scenarios
where otx2_ptp is deallocated by otx2_ptp_destroy(), while synctstamp_work
remains active and attempts to dereference otx2_ptp in otx2_sync_tstamp().
Furthermore, the synctstamp_work is cyclic, the likelihood of triggering
the bug is nonnegligible.
A typical race condition is illustrated below:
CPU 0 (cleanup) | CPU 1 (delayed work callback)
otx2_remove() |
otx2_ptp_destroy() | otx2_sync_tstamp()
cancel_delayed_work() |
kfree(ptp) |
| ptp = container_of(...); //UAF
| ptp-> //UAF
This is confirmed by a KASAN report:
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0
Write of size 8 at addr ffff88800aa09a18 by task bash/136
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcf/0x610
? __run_timer_base.part.0+0x7d7/0x8c0
kasan_report+0xb8/0xf0
? __run_timer_base.part.0+0x7d7/0x8c0
__run_timer_base.part.0+0x7d7/0x8c0
? __pfx___run_timer_base.part.0+0x10/0x10
? __pfx_read_tsc+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
run_timer_softirq+0xd1/0x190
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
Allocated by task 1:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
otx2_ptp_init+0xb1/0x860
otx2_probe+0x4eb/0xc30
local_pci_probe+0xdc/0x190
pci_device_probe+0x2fe/0x470
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__driver_attach+0xd2/0x310
bus_for_each_dev+0xed/0x170
bus_add_driver+0x208/0x500
driver_register+0x132/0x460
do_one_initcall+0x89/0x300
kernel_init_freeable+0x40d/0x720
kernel_init+0x1a/0x150
ret_from_fork+0x10c/0x1a0
ret_from_fork_asm+0x1a/0x30
Freed by task 136:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x3f/0x50
kfree+0x137/0x370
otx2_ptp_destroy+0x38/0x80
otx2_remove+0x10d/0x4c0
pci_device_remove+0xa6/0x1d0
device_release_driver_internal+0xf8/0x210
pci_stop_bus_device+0x105/0x150
pci_stop_and_remove_bus_device_locked+0x15/0x30
remove_store+0xcc/0xe0
kernfs_fop_write_iter+0x2c3/0x440
vfs_write+0x871/0xd70
ksys_write+0xee/0x1c0
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the delayed work item is properly canceled before the otx2_ptp is
deallocated.
This bug was initially identified through static analysis. To reproduce
and test it, I simulated the OcteonTX2 PCI device in QEMU and introduced
artificial delays within the otx2_sync_tstamp() function to increase the
likelihood of triggering the bug.
Published Oct 4, 2025 · Updated Jul 30, 2026
Critical · CVSS 9.4
In the Linux kernel, the following vulnerability has been resolved:
ksmbd: smbdirect: validate data_offset and data_length field of smb_direct_data_transfer
If data_offset and data_length of smb_direct_data_transfer struct are
invalid, out of bounds issue could happen.
This patch validate data_offset and data_length field in recv_done.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.5
In the Linux kernel, the following vulnerability has been resolved:
ksmbd: smbdirect: verify remaining_data_length respects max_fragmented_recv_size
This is inspired by the check for data_offset + data_length.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
zram: fix slot write race condition
Parallel concurrent writes to the same zram index result in leaked
zsmalloc handles. Schematically we can have something like this:
CPU0 CPU1
zram_slot_lock()
zs_free(handle)
zram_slot_lock()
zram_slot_lock()
zs_free(handle)
zram_slot_lock()
compress compress
handle = zs_malloc() handle = zs_malloc()
zram_slot_lock
zram_set_handle(handle)
zram_slot_lock
zram_slot_lock
zram_set_handle(handle)
zram_slot_lock
Either CPU0 or CPU1 zsmalloc handle will leak because zs_free() is done
too early. In fact, we need to reset zram entry right before we set its
new handle, all under the same slot lock scope.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
iommu/s390: Fix memory corruption when using identity domain
zpci_get_iommu_ctrs() returns counter information to be reported as part
of device statistics; these counters are stored as part of the s390_domain.
The problem, however, is that the identity domain is not backed by an
s390_domain and so the conversion via to_s390_domain() yields a bad address
that is zero'd initially and read on-demand later via a sysfs read.
These counters aren't necessary for the identity domain; just return NULL
in this case.
This issue was discovered via KASAN with reports that look like:
BUG: KASAN: global-out-of-bounds in zpci_fmb_enable_device
when using the identity domain for a device on s390.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
ASoC: codec: sma1307: Fix memory corruption in sma1307_setting_loaded()
The sma1307->set.header_size is how many integers are in the header
(there are 8 of them) but instead of allocating space of 8 integers
we allocate 8 bytes. This leads to memory corruption when we copy data
it on the next line:
memcpy(sma1307->set.header, data,
sma1307->set.header_size * sizeof(int));
Also since we're immediately copying over the memory in ->set.header,
there is no need to zero it in the allocator. Use devm_kmalloc_array()
to allocate the memory instead.
Published Oct 4, 2025 · Updated Jul 30, 2026
Critical · CVSS 9.4
In the Linux kernel, the following vulnerability has been resolved:
smb: client: let recv_done verify data_offset, data_length and remaining_data_length
This is inspired by the related server fixes.
Published Oct 4, 2025 · Updated Jul 30, 2026
Critical · CVSS 9.8
In the Linux kernel, the following vulnerability has been resolved:
smb: client: let smbd_destroy() call disable_work_sync(&info->post_send_credits_work)
In smbd_destroy() we may destroy the memory so we better
wait until post_send_credits_work is no longer pending
and will never be started again.
I actually just hit the case using rxe:
WARNING: CPU: 0 PID: 138 at drivers/infiniband/sw/rxe/rxe_verbs.c:1032 rxe_post_recv+0x1ee/0x480 [rdma_rxe]
...
[ 5305.686979] [ T138] smbd_post_recv+0x445/0xc10 [cifs]
[ 5305.687135] [ T138] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5305.687149] [ T138] ? __kasan_check_write+0x14/0x30
[ 5305.687185] [ T138] ? __pfx_smbd_post_recv+0x10/0x10 [cifs]
[ 5305.687329] [ T138] ? __pfx__raw_spin_lock_irqsave+0x10/0x10
[ 5305.687356] [ T138] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5305.687368] [ T138] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5305.687378] [ T138] ? _raw_spin_unlock_irqrestore+0x11/0x60
[ 5305.687389] [ T138] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5305.687399] [ T138] ? get_receive_buffer+0x168/0x210 [cifs]
[ 5305.687555] [ T138] smbd_post_send_credits+0x382/0x4b0 [cifs]
[ 5305.687701] [ T138] ? __pfx_smbd_post_send_credits+0x10/0x10 [cifs]
[ 5305.687855] [ T138] ? __pfx___schedule+0x10/0x10
[ 5305.687865] [ T138] ? __pfx__raw_spin_lock_irq+0x10/0x10
[ 5305.687875] [ T138] ? queue_delayed_work_on+0x8e/0xa0
[ 5305.687889] [ T138] process_one_work+0x629/0xf80
[ 5305.687908] [ T138] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5305.687917] [ T138] ? __kasan_check_write+0x14/0x30
[ 5305.687933] [ T138] worker_thread+0x87f/0x1570
...
It means rxe_post_recv was called after rdma_destroy_qp().
This happened because put_receive_buffer() was triggered
by ib_drain_qp() and called:
queue_work(info->workqueue, &info->post_send_credits_work);
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
crypto: af_alg - Set merge to zero early in af_alg_sendmsg
If an error causes af_alg_sendmsg to abort, ctx->merge may contain
a garbage value from the previous loop. This may then trigger a
crash on the next entry into af_alg_sendmsg when it attempts to do
a merge that can't be done.
Fix this by setting ctx->merge to zero near the start of the loop.
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 8.4
In the Linux kernel, the following vulnerability has been resolved:
ASoC: simple-card-utils: Don't use __free(device_node) at graph_util_parse_dai()
commit 419d1918105e ("ASoC: simple-card-utils: use __free(device_node) for
device node") uses __free(device_node) for dlc->of_node, but we need to
keep it while driver is in use.
Don't use __free(device_node) in graph_util_parse_dai().
Published Apr 18, 2025 · Updated Jul 30, 2026
High · CVSS 7.5
In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix smbdirect_recv_io leak in smbd_negotiate() error path
During tests of another unrelated patch I was able to trigger this
error: Objects remaining on __kmem_cache_shutdown()
Published Oct 4, 2025 · Updated Jul 30, 2026
High · CVSS 7.1
In the Linux kernel, the following vulnerability has been resolved:
i2c: rtl9300: ensure data length is within supported range
Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer'
to ensure the data length isn't within the supported range. In
particular a data length of 0 is not supported by the hardware and
causes unintended or destructive behaviour.
This limitation becomes obvious when looking at the register
documentation [1]. 4 bits are reserved for DATA_WIDTH and the value
of these 4 bits is used as N + 1, allowing a data length range of
1 <= len <= 16.
Affected by this is the SMBus Quick Operation which works with a data
length of 0. Passing 0 as the length causes an underflow of the value
due to:
(len - 1) & 0xf
and effectively specifying a transfer length of 16 via the registers.
This causes a 16-byte write operation instead of a Quick Write. For
example, on SFP modules without write-protected EEPROM this soft-bricks
them by overwriting some initial bytes.
For completeness, also add a quirk for the zero length.
[1] https://svanheule.net/realtek/longan/register/i2c_mst1_ctrl2
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
ceph: fix race condition validating r_parent before applying state
Add validation to ensure the cached parent directory inode matches the
directory info in MDS replies. This prevents client-side race conditions
where concurrent operations (e.g. rename) cause r_parent to become stale
between request initiation and reply processing, which could lead to
applying state changes to incorrect directory inodes.
[ idryomov: folded a kerneldoc fixup and a follow-up fix from Alex to
move CEPH_CAP_PIN reference when r_parent is updated:
When the parent directory lock is not held, req->r_parent can become
stale and is updated to point to the correct inode. However, the
associated CEPH_CAP_PIN reference was not being adjusted. The
CEPH_CAP_PIN is a reference on an inode that is tracked for
accounting purposes. Moving this pin is important to keep the
accounting balanced. When the pin was not moved from the old parent
to the new one, it created two problems: The reference on the old,
stale parent was never released, causing a reference leak.
A reference for the new parent was never acquired, creating the risk
of a reference underflow later in ceph_mdsc_release_request(). This
patch corrects the logic by releasing the pin from the old parent and
acquiring it for the new parent when r_parent is switched. This
ensures reference accounting stays balanced. ]
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
erofs: fix invalid algorithm for encoded extents
The current algorithm sanity checks do not properly apply to new
encoded extents.
Unify the algorithm check with Z_EROFS_COMPRESSION(_RUNTIME)_MAX
and ensure consistency with sbi->available_compr_algs.
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 8.8
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: add missing check for rx wcid entries
Non-station wcid entries must not be passed to the rx functions.
In case of the global wcid entry, it could even lead to corruption in the wcid
array due to pointer being casted to struct mt7996_sta_link using container_of.
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 8.8
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix linked list corruption
Never leave scheduled wcid entries on the temporary on-stack list
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
net: dev_ioctl: take ops lock in hwtstamp lower paths
ndo hwtstamp callbacks are expected to run under the per-device ops
lock. Make the lower get/set paths consistent with the rest of ndo
invocations.
Kernel log:
WARNING: CPU: 13 PID: 51364 at ./include/net/netdev_lock.h:70 __netdev_update_features+0x4bd/0xe60
...
RIP: 0010:__netdev_update_features+0x4bd/0xe60
...
Call Trace:
<TASK>
netdev_update_features+0x1f/0x60
mlx5_hwtstamp_set+0x181/0x290 [mlx5_core]
mlx5e_hwtstamp_set+0x19/0x30 [mlx5_core]
dev_set_hwtstamp_phylib+0x9f/0x220
dev_set_hwtstamp_phylib+0x9f/0x220
dev_set_hwtstamp+0x13d/0x240
dev_ioctl+0x12f/0x4b0
sock_ioctl+0x171/0x370
__x64_sys_ioctl+0x3f7/0x900
? __sys_setsockopt+0x69/0xb0
do_syscall_64+0x6f/0x2e0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
...
</TASK>
....
---[ end trace 0000000000000000 ]---
Note that the mlx5_hwtstamp_set and mlx5e_hwtstamp_set functions shown
in the trace come from an in progress patch converting the legacy ioctl
to ndo_hwtstamp_get/set and are not present in mainline.
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: remove oem i2c adapter on finish
Fixes a bug where unbinding of the GPU would leave the oem i2c adapter
registered resulting in a null pointer dereference when applications try
to access the invalid device.
(cherry picked from commit 89923fb7ead4fdd37b78dd49962d9bb5892403e6)
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.1
In the Linux kernel, the following vulnerability has been resolved:
mm/slub: avoid accessing metadata when pointer is invalid in object_err()
object_err() reports details of an object for further debugging, such as
the freelist pointer, redzone, etc. However, if the pointer is invalid,
attempting to access object metadata can lead to a crash since it does
not point to a valid object.
One known path to the crash is when alloc_consistency_checks()
determines the pointer to the allocated object is invalid because of a
freelist corruption, and calls object_err() to report it. The debug code
should report and handle the corruption gracefully and not crash in the
process.
In case the pointer is NULL or check_valid_pointer() returns false for
the pointer, only print the pointer value and skip accessing metadata.
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.5
In the Linux kernel, the following vulnerability has been resolved:
net: xilinx: axienet: Add error handling for RX metadata pointer retrieval
Add proper error checking for dmaengine_desc_get_metadata_ptr() which
can return an error pointer and lead to potential crashes or undefined
behaviour if the pointer retrieval fails.
Properly handle the error by unmapping DMA buffer, freeing the skb and
returning early to prevent further processing with invalid data.
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Prevent recovery work from being queued during device removal
Use disable_work_sync() instead of cancel_work_sync() in ivpu_dev_fini()
to ensure that no new recovery work items can be queued after device
removal has started. Previously, recovery work could be scheduled even
after canceling existing work, potentially leading to use-after-free
bugs if recovery accessed freed resources.
Rename ivpu_pm_cancel_recovery() to ivpu_pm_disable_recovery() to better
reflect its new behavior.
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.5
In the Linux kernel, the following vulnerability has been resolved:
netfilter: br_netfilter: do not check confirmed bit in br_nf_local_in() after confirm
When send a broadcast packet to a tap device, which was added to a bridge,
br_nf_local_in() is called to confirm the conntrack. If another conntrack
with the same hash value is added to the hash table, which can be
triggered by a normal packet to a non-bridge device, the below warning
may happen.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 96 at net/bridge/br_netfilter_hooks.c:632 br_nf_local_in+0x168/0x200
CPU: 1 UID: 0 PID: 96 Comm: tap_send Not tainted 6.17.0-rc2-dirty #44 PREEMPT(voluntary)
RIP: 0010:br_nf_local_in+0x168/0x200
Call Trace:
<TASK>
nf_hook_slow+0x3e/0xf0
br_pass_frame_up+0x103/0x180
br_handle_frame_finish+0x2de/0x5b0
br_nf_hook_thresh+0xc0/0x120
br_nf_pre_routing_finish+0x168/0x3a0
br_nf_pre_routing+0x237/0x5e0
br_handle_frame+0x1ec/0x3c0
__netif_receive_skb_core+0x225/0x1210
__netif_receive_skb_one_core+0x37/0xa0
netif_receive_skb+0x36/0x160
tun_get_user+0xa54/0x10c0
tun_chr_write_iter+0x65/0xb0
vfs_write+0x305/0x410
ksys_write+0x60/0xd0
do_syscall_64+0xa4/0x260
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
---[ end trace 0000000000000000 ]---
To solve the hash conflict, nf_ct_resolve_clash() try to merge the
conntracks, and update skb->_nfct. However, br_nf_local_in() still use the
old ct from local variable 'nfct' after confirm(), which leads to this
warning.
If confirm() does not insert the conntrack entry and return NF_DROP, the
warning may also occur. There is no need to reserve the WARN_ON_ONCE, just
remove it.
Published Oct 1, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
fuse: Block access to folio overlimit
syz reported a slab-out-of-bounds Write in fuse_dev_do_write.
When the number of bytes to be retrieved is truncated to the upper limit
by fc->max_pages and there is an offset, the oob is triggered.
Add a loop termination condition to prevent overruns.
Published Sep 23, 2025 · Updated Jul 30, 2026
High · CVSS 8.4
In the Linux kernel, the following vulnerability has been resolved:
drm/mediatek: fix potential OF node use-after-free
The for_each_child_of_node() helper drops the reference it takes to each
node as it iterates over children and an explicit of_node_put() is only
needed when exiting the loop early.
Drop the recently introduced bogus additional reference count decrement
at each iteration that could potentially lead to a use-after-free.
Published Sep 23, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
kernfs: Fix UAF in polling when open file is released
A use-after-free (UAF) vulnerability was identified in the PSI (Pressure
Stall Information) monitoring mechanism:
BUG: KASAN: slab-use-after-free in psi_trigger_poll+0x3c/0x140
Read of size 8 at addr ffff3de3d50bd308 by task systemd/1
psi_trigger_poll+0x3c/0x140
cgroup_pressure_poll+0x70/0xa0
cgroup_file_poll+0x8c/0x100
kernfs_fop_poll+0x11c/0x1c0
ep_item_poll.isra.0+0x188/0x2c0
Allocated by task 1:
cgroup_file_open+0x88/0x388
kernfs_fop_open+0x73c/0xaf0
do_dentry_open+0x5fc/0x1200
vfs_open+0xa0/0x3f0
do_open+0x7e8/0xd08
path_openat+0x2fc/0x6b0
do_filp_open+0x174/0x368
Freed by task 8462:
cgroup_file_release+0x130/0x1f8
kernfs_drain_open_files+0x17c/0x440
kernfs_drain+0x2dc/0x360
kernfs_show+0x1b8/0x288
cgroup_file_show+0x150/0x268
cgroup_pressure_write+0x1dc/0x340
cgroup_file_write+0x274/0x548
Reproduction Steps:
1. Open test/cpu.pressure and establish epoll monitoring
2. Disable monitoring: echo 0 > test/cgroup.pressure
3. Re-enable monitoring: echo 1 > test/cgroup.pressure
The race condition occurs because:
1. When cgroup.pressure is disabled (echo 0 > cgroup.pressure), it:
- Releases PSI triggers via cgroup_file_release()
- Frees of->priv through kernfs_drain_open_files()
2. While epoll still holds reference to the file and continues polling
3. Re-enabling (echo 1 > cgroup.pressure) accesses freed of->priv
epolling disable/enable cgroup.pressure
fd=open(cpu.pressure)
while(1)
...
epoll_wait
kernfs_fop_poll
kernfs_get_active = true echo 0 > cgroup.pressure
... cgroup_file_show
kernfs_show
// inactive kn
kernfs_drain_open_files
cft->release(of);
kfree(ctx);
...
kernfs_get_active = false
echo 1 > cgroup.pressure
kernfs_show
kernfs_activate_one(kn);
kernfs_fop_poll
kernfs_get_active = true
cgroup_file_poll
psi_trigger_poll
// UAF
...
end: close(fd)
To address this issue, introduce kernfs_get_active_of() for kernfs open
files to obtain active references. This function will fail if the open file
has been released. Replace kernfs_get_active() with kernfs_get_active_of()
to prevent further operations on released file descriptors.
Published Sep 23, 2025 · Updated Jul 30, 2026
Critical · CVSS 9.8
In the Linux kernel, the following vulnerability has been resolved:
libceph: fix invalid accesses to ceph_connection_v1_info
There is a place where generic code in messenger.c is reading and
another place where it is writing to con->v1 union member without
checking that the union member is active (i.e. msgr1 is in use).
On 64-bit systems, con->v1.auth_retry overlaps with con->v2.out_iter,
so such a read is almost guaranteed to return a bogus value instead of
0 when msgr2 is in use. This ends up being fairly benign because the
side effect is just the invalidation of the authorizer and successive
fetching of new tickets.
con->v1.connect_seq overlaps with con->v2.conn_bufs and the fact that
it's being written to can cause more serious consequences, but luckily
it's not something that happens often.
Published Sep 23, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
can: xilinx_can: xcan_write_frame(): fix use-after-free of transmitted SKB
can_put_echo_skb() takes ownership of the SKB and it may be freed
during or after the call.
However, xilinx_can xcan_write_frame() keeps using SKB after the call.
Fix that by only calling can_put_echo_skb() after the code is done
touching the SKB.
The tx_lock is held for the entire xcan_write_frame() execution and
also on the can_get_echo_skb() side so the order of operations does not
matter.
An earlier fix commit 3d3c817c3a40 ("can: xilinx_can: Fix usage of skb
memory") did not move the can_put_echo_skb() call far enough.
[mkl: add "commit" in front of sha1 in patch description]
[mkl: fix indention]
Published Sep 23, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
hsr: hold rcu and dev lock for hsr_get_port_ndev
hsr_get_port_ndev calls hsr_for_each_port, which need to hold rcu lock.
On the other hand, before return the port device, we need to hold the
device reference to avoid UaF in the caller function.
Published Sep 23, 2025 · Updated Jul 30, 2026
High · CVSS 8.4
In the Linux kernel, the following vulnerability has been resolved:
dmaengine: ti: edma: Fix memory allocation size for queue_priority_map
Fix a critical memory allocation bug in edma_setup_from_hw() where
queue_priority_map was allocated with insufficient memory. The code
declared queue_priority_map as s8 (*)[2] (pointer to array of 2 s8),
but allocated memory using sizeof(s8) instead of the correct size.
This caused out-of-bounds memory writes when accessing:
queue_priority_map[i][0] = i;
queue_priority_map[i][1] = i;
The bug manifested as kernel crashes with "Oops - undefined instruction"
on ARM platforms (BeagleBoard-X15) during EDMA driver probe, as the
memory corruption triggered kernel hardening features on Clang.
Change the allocation to use sizeof(*queue_priority_map) which
automatically gets the correct size for the 2D array structure.
Published Sep 23, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
erofs: fix runtime warning on truncate_folio_batch_exceptionals()
Commit 0e2f80afcfa6("fs/dax: ensure all pages are idle prior to
filesystem unmount") introduced the WARN_ON_ONCE to capture whether
the filesystem has removed all DAX entries or not and applied the
fix to xfs and ext4.
Apply the missed fix on erofs to fix the runtime warning:
[ 5.266254] ------------[ cut here ]------------
[ 5.266274] WARNING: CPU: 6 PID: 3109 at mm/truncate.c:89 truncate_folio_batch_exceptionals+0xff/0x260
[ 5.266294] Modules linked in:
[ 5.266999] CPU: 6 UID: 0 PID: 3109 Comm: umount Tainted: G S 6.16.0+ #6 PREEMPT(voluntary)
[ 5.267012] Tainted: [S]=CPU_OUT_OF_SPEC
[ 5.267017] Hardware name: Dell Inc. OptiPlex 5000/05WXFV, BIOS 1.5.1 08/24/2022
[ 5.267024] RIP: 0010:truncate_folio_batch_exceptionals+0xff/0x260
[ 5.267076] Code: 00 00 41 39 df 7f 11 eb 78 83 c3 01 49 83 c4 08 41 39 df 74 6c 48 63 f3 48 83 fe 1f 0f 83 3c 01 00 00 43 f6 44 26 08 01 74 df <0f> 0b 4a 8b 34 22 4c 89 ef 48 89 55 90 e8 ff 54 1f 00 48 8b 55 90
[ 5.267083] RSP: 0018:ffffc900013f36c8 EFLAGS: 00010202
[ 5.267095] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 5.267101] RDX: ffffc900013f3790 RSI: 0000000000000000 RDI: ffff8882a1407898
[ 5.267108] RBP: ffffc900013f3740 R08: 0000000000000000 R09: 0000000000000000
[ 5.267113] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
[ 5.267119] R13: ffff8882a1407ab8 R14: ffffc900013f3888 R15: 0000000000000001
[ 5.267125] FS: 00007aaa8b437800(0000) GS:ffff88850025b000(0000) knlGS:0000000000000000
[ 5.267132] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5.267138] CR2: 00007aaa8b3aac10 CR3: 000000024f764000 CR4: 0000000000f52ef0
[ 5.267144] PKRU: 55555554
[ 5.267150] Call Trace:
[ 5.267154] <TASK>
[ 5.267181] truncate_inode_pages_range+0x118/0x5e0
[ 5.267193] ? save_trace+0x54/0x390
[ 5.267296] truncate_inode_pages_final+0x43/0x60
[ 5.267309] evict+0x2a4/0x2c0
[ 5.267339] dispose_list+0x39/0x80
[ 5.267352] evict_inodes+0x150/0x1b0
[ 5.267376] generic_shutdown_super+0x41/0x180
[ 5.267390] kill_block_super+0x1b/0x50
[ 5.267402] erofs_kill_sb+0x81/0x90 [erofs]
[ 5.267436] deactivate_locked_super+0x32/0xb0
[ 5.267450] deactivate_super+0x46/0x60
[ 5.267460] cleanup_mnt+0xc3/0x170
[ 5.267475] __cleanup_mnt+0x12/0x20
[ 5.267485] task_work_run+0x5d/0xb0
[ 5.267499] exit_to_user_mode_loop+0x144/0x170
[ 5.267512] do_syscall_64+0x2b9/0x7c0
[ 5.267523] ? __lock_acquire+0x665/0x2ce0
[ 5.267535] ? __lock_acquire+0x665/0x2ce0
[ 5.267560] ? lock_acquire+0xcd/0x300
[ 5.267573] ? find_held_lock+0x31/0x90
[ 5.267582] ? mntput_no_expire+0x97/0x4e0
[ 5.267606] ? mntput_no_expire+0xa1/0x4e0
[ 5.267625] ? mntput+0x24/0x50
[ 5.267634] ? path_put+0x1e/0x30
[ 5.267647] ? do_faccessat+0x120/0x2f0
[ 5.267677] ? do_syscall_64+0x1a2/0x7c0
[ 5.267686] ? from_kgid_munged+0x17/0x30
[ 5.267703] ? from_kuid_munged+0x13/0x30
[ 5.267711] ? __do_sys_getuid+0x3d/0x50
[ 5.267724] ? do_syscall_64+0x1a2/0x7c0
[ 5.267732] ? irqentry_exit+0x77/0xb0
[ 5.267743] ? clear_bhb_loop+0x30/0x80
[ 5.267752] ? clear_bhb_loop+0x30/0x80
[ 5.267765] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 5.267772] RIP: 0033:0x7aaa8b32a9fb
[ 5.267781] Code: c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 f3 0f 1e fa 31 f6 e9 05 00 00 00 0f 1f 44 00 00 f3 0f 1e fa b8 a6 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 05 c3 0f 1f 40 00 48 8b 15 e9 83 0d 00 f7 d8
[ 5.267787] RSP: 002b:00007ffd7c4c9468 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[ 5.267796] RAX: 0000000000000000 RBX: 00005a61592a8b00 RCX: 00007aaa8b32a9fb
[ 5.267802] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00005a61592b2080
[ 5.267806] RBP: 00007ffd7c4c9540 R08: 00007aaa8b403b20 R09: 0000000000000020
[ 5.267812] R10: 0000000000000001 R11: 0000000000000246 R12: 00005a61592a8c00
[ 5.267817] R13: 00000000
---truncated---
Published Sep 23, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
fs: writeback: fix use-after-free in __mark_inode_dirty()
An use-after-free issue occurred when __mark_inode_dirty() get the
bdi_writeback that was in the progress of switching.
CPU: 1 PID: 562 Comm: systemd-random- Not tainted 6.6.56-gb4403bd46a8e #1
......
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __mark_inode_dirty+0x124/0x418
lr : __mark_inode_dirty+0x118/0x418
sp : ffffffc08c9dbbc0
........
Call trace:
__mark_inode_dirty+0x124/0x418
generic_update_time+0x4c/0x60
file_modified+0xcc/0xd0
ext4_buffered_write_iter+0x58/0x124
ext4_file_write_iter+0x54/0x704
vfs_write+0x1c0/0x308
ksys_write+0x74/0x10c
__arm64_sys_write+0x1c/0x28
invoke_syscall+0x48/0x114
el0_svc_common.constprop.0+0xc0/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x40/0xe4
el0t_64_sync_handler+0x120/0x12c
el0t_64_sync+0x194/0x198
Root cause is:
systemd-random-seed kworker
----------------------------------------------------------------------
___mark_inode_dirty inode_switch_wbs_work_fn
spin_lock(&inode->i_lock);
inode_attach_wb
locked_inode_to_wb_and_lock_list
get inode->i_wb
spin_unlock(&inode->i_lock);
spin_lock(&wb->list_lock)
spin_lock(&inode->i_lock)
inode_io_list_move_locked
spin_unlock(&wb->list_lock)
spin_unlock(&inode->i_lock)
spin_lock(&old_wb->list_lock)
inode_do_switch_wbs
spin_lock(&inode->i_lock)
inode->i_wb = new_wb
spin_unlock(&inode->i_lock)
spin_unlock(&old_wb->list_lock)
wb_put_many(old_wb, nr_switched)
cgwb_release
old wb released
wb_wakeup_delayed() accesses wb,
then trigger the use-after-free
issue
Fix this race condition by holding inode spinlock until
wb_wakeup_delayed() finished.
Published Sep 19, 2025 · Updated Jul 30, 2026
High · CVSS 8.8
In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: fix use-after-free in cmp_bss()
Following bss_free() quirk introduced in commit 776b3580178f
("cfg80211: track hidden SSID networks properly"), adjust
cfg80211_update_known_bss() to free the last beacon frame
elements only if they're not shared via the corresponding
'hidden_beacon_bss' pointer.
Published Sep 19, 2025 · Updated Jul 30, 2026
High · CVSS 7.8
In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix use-after-free when rescheduling brcmf_btcoex_info work
The brcmf_btcoex_detach() only shuts down the btcoex timer, if the
flag timer_on is false. However, the brcmf_btcoex_timerfunc(), which
runs as timer handler, sets timer_on to false. This creates critical
race conditions:
1.If brcmf_btcoex_detach() is called while brcmf_btcoex_timerfunc()
is executing, it may observe timer_on as false and skip the call to
timer_shutdown_sync().
2.The brcmf_btcoex_timerfunc() may then reschedule the brcmf_btcoex_info
worker after the cancel_work_sync() has been executed, resulting in
use-after-free bugs.
The use-after-free bugs occur in two distinct scenarios, depending on
the timing of when the brcmf_btcoex_info struct is freed relative to
the execution of its worker thread.
Scenario 1: Freed before the worker is scheduled
The brcmf_btcoex_info is deallocated before the worker is scheduled.
A race condition can occur when schedule_work(&bt_local->work) is
called after the target memory has been freed. The sequence of events
is detailed below:
CPU0 | CPU1
brcmf_btcoex_detach | brcmf_btcoex_timerfunc
| bt_local->timer_on = false;
if (cfg->btcoex->timer_on) |
... |
cancel_work_sync(); |
... |
kfree(cfg->btcoex); // FREE |
| schedule_work(&bt_local->work); // USE
Scenario 2: Freed after the worker is scheduled
The brcmf_btcoex_info is freed after the worker has been scheduled
but before or during its execution. In this case, statements within
the brcmf_btcoex_handler() — such as the container_of macro and
subsequent dereferences of the brcmf_btcoex_info object will cause
a use-after-free access. The following timeline illustrates this
scenario:
CPU0 | CPU1
brcmf_btcoex_detach | brcmf_btcoex_timerfunc
| bt_local->timer_on = false;
if (cfg->btcoex->timer_on) |
... |
cancel_work_sync(); |
... | schedule_work(); // Reschedule
|
kfree(cfg->btcoex); // FREE | brcmf_btcoex_handler() // Worker
/* | btci = container_of(....); // USE
The kfree() above could | ...
also occur at any point | btci-> // USE
during the worker's execution|
*/ |
To resolve the race conditions, drop the conditional check and call
timer_shutdown_sync() directly. It can deactivate the timer reliably,
regardless of its current state. Once stopped, the timer_on state is
then set to false.
Published Sep 19, 2025 · Updated Jul 30, 2026
High · CVSS 8.8
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix list corruption after hardware restart
Since stations are recreated from scratch, all lists that wcids are added
to must be cleared before calling ieee80211_restart_hw.
Set wcid->sta = 0 for each wcid entry in order to ensure that they are
not added again before they are ready.
Published Sep 19, 2025 · Updated Jul 30, 2026
High · CVSS 8
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Fix use-after-free in l2cap_sock_cleanup_listen()
syzbot reported the splat below without a repro.
In the splat, a single thread calling bt_accept_dequeue() freed sk
and touched it after that.
The root cause would be the racy l2cap_sock_cleanup_listen() call
added by the cited commit.
bt_accept_dequeue() is called under lock_sock() except for
l2cap_sock_release().
Two threads could see the same socket during the list iteration
in bt_accept_dequeue():
CPU1 CPU2 (close())
---- ----
sock_hold(sk) sock_hold(sk);
lock_sock(sk) <-- block close()
sock_put(sk)
bt_accept_unlink(sk)
sock_put(sk) <-- refcnt by bt_accept_enqueue()
release_sock(sk)
lock_sock(sk)
sock_put(sk)
bt_accept_unlink(sk)
sock_put(sk) <-- last refcnt
bt_accept_unlink(sk) <-- UAF
Depending on the timing, the other thread could show up in the
"Freed by task" part.
Let's call l2cap_sock_cleanup_listen() under lock_sock() in
l2cap_sock_release().
[0]:
BUG: KASAN: slab-use-after-free in debug_spin_lock_before kernel/locking/spinlock_debug.c:86 [inline]
BUG: KASAN: slab-use-after-free in do_raw_spin_lock+0x26f/0x2b0 kernel/locking/spinlock_debug.c:115
Read of size 4 at addr ffff88803b7eb1c4 by task syz.5.3276/16995
CPU: 3 UID: 0 PID: 16995 Comm: syz.5.3276 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xcd/0x630 mm/kasan/report.c:482
kasan_report+0xe0/0x110 mm/kasan/report.c:595
debug_spin_lock_before kernel/locking/spinlock_debug.c:86 [inline]
do_raw_spin_lock+0x26f/0x2b0 kernel/locking/spinlock_debug.c:115
spin_lock_bh include/linux/spinlock.h:356 [inline]
release_sock+0x21/0x220 net/core/sock.c:3746
bt_accept_dequeue+0x505/0x600 net/bluetooth/af_bluetooth.c:312
l2cap_sock_cleanup_listen+0x5c/0x2a0 net/bluetooth/l2cap_sock.c:1451
l2cap_sock_release+0x5c/0x210 net/bluetooth/l2cap_sock.c:1425
__sock_release+0xb3/0x270 net/socket.c:649
sock_close+0x1c/0x30 net/socket.c:1439
__fput+0x3ff/0xb70 fs/file_table.c:468
task_work_run+0x14d/0x240 kernel/task_work.c:227
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
exit_to_user_mode_loop+0xeb/0x110 kernel/entry/common.c:43
exit_to_user_mode_prepare include/linux/irq-entry-common.h:225 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:175 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:210 [inline]
do_syscall_64+0x3f6/0x4c0 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f2accf8ebe9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffdb6cb1378 EFLAGS: 00000246 ORIG_RAX: 00000000000001b4
RAX: 0000000000000000 RBX: 00000000000426fb RCX: 00007f2accf8ebe9
RDX: 0000000000000000 RSI: 000000000000001e RDI: 0000000000000003
RBP: 00007f2acd1b7da0 R08: 0000000000000001 R09: 00000012b6cb166f
R10: 0000001b30e20000 R11: 0000000000000246 R12: 00007f2acd1b609c
R13: 00007f2acd1b6090 R14: ffffffffffffffff R15: 00007ffdb6cb1490
</TASK>
Allocated by task 5326:
kasan_save_stack+0x33/0x60 mm/kasan/common.c:47
kasan_save_track+0x14/0x30 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:388 [inline]
__kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:405
kasan_kmalloc include/linux/kasan.h:260 [inline]
__do_kmalloc_node mm/slub.c:4365 [inline]
__kmalloc_nopro
---truncated---
Published Sep 19, 2025 · Updated Jul 30, 2026
